位置:51电子网 » 企业新闻

PGA-103+

发布时间:2019/11/8 17:35:00 访问次数:69发布企业:深圳市创宝来科技有限公司

Monolithic Amplifier
Notes
A. Performance and quality attributes and conditions not expressly stated in this specification document are intended to be excluded and do not form a part of this specification document.
B. Electrical specifications and performance data contained in this specification document are based on Mini-Circuit’s applicable established test performance criteria and measurement instructions.
C. The parts covered by this specification document are subject to Mini-Circuits standard limited warranty and terms and conditions (collectively, “Standard Terms”); Purchasers of this part are entitled
to the rights and benefits contained therein. For a full statement of the Standard Terms and the exclusive rights and remedies thereunder, please visit Mini-Circuits’ website at www.minicircuits.com/MCLStore/terms.jsp
Mini-Circuits®
www.minicircuits.com P.O. Box 350166, Brooklyn, NY 11235-0003 (718) 934-4500 sales@minicircuits.com Page 1 of 5
The Big Deal
Product Overview
PGA-103+ (RoHS compliant) is an advanced wideband amplifier fabricated using E-PHEMT technology
and offers extremely high dynamic range over a broad frequency range and with low noise figure. In addition,
the PGA-103+ has good input and output return loss over a broad frequency range without the need
for external matching components and has demonstrated excellent reliability. Lead finish is SnAgNi. It has
repeatable performance from lot to lot and is enclosed in a SOT-89 package for very good thermal performance.
Feature Advantages
Broad Band: 0.05 to 4.0 GHz
Broadband covering primary wireless communications bands:
Cellular, PCS, LTE, WiMAX
Ultra High IP3
Versus DC power Consumption:
45 dBm typical at 2 GHz at +5.0V
Supply Voltage and only 97mA
The PGA-103+ provides excellent IP3 performance relative to device size and power
consumption. The combination of the design and E-PHEMT Structure provides enhanced
linearity over a broad frequency range as evidence in the IP3 being typically 20
dB above the P 1dB point. This feature makes this amplifier ideal for use in:
• Driver amplifiers for complex waveform up converter paths
• Drivers in linearized transmit systems
• Secondary amplifiers in ultra High Dynamic range receivers
Low Noise Figure:
0.6 dB up to 1.0 GHz
A unique feature of the PGA-103+ which separates this design from all competitors is the
low noise figure performance in combination with the high dynamic range.
PGA-103+
Key Features
50Ω 0.05 to 4 GHz
SOT-89 PACKAGE
• Ultra High IP3
• Broadband High Dynamic Range
• May be used as a replacement for RFMD SPF-5189Za,b
Ultra Linear Low Noise
Notes:
a. Suitability for model replacement within a particular system must be determined by and is solely the responsibility of the customer based on, among other things, electrical
performance criteria, stimulus conditions, application, compatibility with other components and environmental conditions and stresses.
b. The RFMD SPF-5189Z part number is used for identification and comparison purposes only.
Monolithic Amplifier
Notes
A. Performance and quality attributes and conditions not expressly stated in this specification document are intended to be excluded and do not form a part of this specification document.
B. Electrical specifications and performance data contained in this specification document are based on Mini-Circuit’s applicable established test performance criteria and measurement instructions.
C. The parts covered by this specification document are subject to Mini-Circuits standard limited warranty and terms and conditions (collectively, “Standard Terms”); Purchasers of this part are entitled
to the rights and benefits contained therein. For a full statement of the Standard Terms and the exclusive rights and remedies thereunder, please visit Mini-Circuits’ website at www.minicircuits.com/MCLStore/terms.jsp
Mini-Circuits®
www.minicircuits.com P.O. Box 350166, Brooklyn, NY 11235-0003 (718) 934-4500 sales@minicircuits.com Page 2 of 5
simplified schematic and pin description
Function Pin Number Description
RF IN 1
RF input pin. This pin requires the use of an external DC blocking capacitor chosen for
the frequency of operation.
RF-OUT and DC-IN 3
RF output and bias pin. DC voltage is present on this pin; therefore a DC blocking
capacitor is necessary for proper operation. An RF choke is needed to feed DC bias
without loss of RF signal due to the bias connection, as shown in “Recommended Application
Circuit”, Fig. 2
GND 2,4
Connections to ground. Use via holes as shown in “Suggested Layout for PCB Design”
to reduce ground path inductance for best performance.
0.05-4 GHz
CASE STYLE: DF782
PGA-103+
Product Features
• 5V/3V operation
• High IP3, 45 dBm typ. at 2 GHz, Vd=5V
• Low Noise Figure, 0.6 at 1 GHz; 0.9 dB at 2 GHz
• Gain, 11.0 dB typ. at 2 GHz
• P1dB 22.5 dBm typ. at 2 GHz at Vd=5V
• Protected under US Patent 8,803,612
REV. A
M151107
PGA-103+
TH/RS/CP
150924
General Description
PGA-103+ (RoHS compliant) is an advanced wideband amplifier fabricated using E-PHEMT technology
and offers extremely high dynamic range over a broad frequency range and with low noise figure. In
addition, the PGA-103+ has good input and output return loss over a broad frequency range without the
need for external matching components. Lead finish is SnAgNi. It has repeatable performance from lot to
lot and is enclosed in a SOT-89 package for very good thermal performance.
Typical Applications
• Base station infrastructure
• Portable Wireless
• CATV & DBS
• MMDS & Wireless LAN
• LTE
3 RF-OUT & DC-IN
2 GROUND
1 RF-IN
RF-IN 4 RF-OUT
and DC-IN
GND
Ultra Linear Low Noise
+RoHS Compliant
The +Suffix identifies RoHS Compliance. See our web site
for RoHS Compliance methodologies and qualifications
Notes:
a. Suitability for model replacement within a particular system must be determined by and is solely the responsibility of the customer based on, among other things, electrical
performance criteria, stimulus conditions, application, compatibility with other components and environmental conditions and stresses.
b. The RFMD SPF-5189Z part number is used for identification and comparison purposes only.
Notes
A. Performance and quality attributes and conditions not expressly stated in this specification document are intended to be excluded and do not form a part of this specification document.
B. Electrical specifications and performance data contained in this specification document are based on Mini-Circuit’s applicable established test performance criteria and measurement instructions.
C. The parts covered by this specification document are subject to Mini-Circuits standard limited warranty and terms and conditions (collectively, “Standard Terms”); Purchasers of this part are entitled
to the rights and benefits contained therein. For a full statement of the Standard Terms and the exclusive rights and remedies thereunder, please visit Mini-Circuits’ website at www.minicircuits.com/MCLStore/terms.jsp
Mini-Circuits®
www.minicircuits.com P.O. Box 350166, Brooklyn, NY 11235-0003 (718) 934-4500 sales@minicircuits.com
Monolithic E-PHEMT MMIC Amplifier
Page 3 of 5
Parameter Ratings
Operating Temperature (ground lead) -40°C to 85°C
Storage Temperature -65°C to 150°C
Operating Current at 5.0V 200 mA
Power Dissipation at 5.0V 1W
Input Power (CW)
+21 dBm (50 to 2000 MHz)
+26 dBm (2000 to 4000 MHz)
DC Voltage on Pin 3 6V
Note:
Permanent damage may occur if any of these limits are exceeded.
Electrical maximum ratings are not intended for continuous normal operation.
Absolute Maximum Ratings
Electrical Specifications(1) at 25°C, 50Ω, unless noted
PGA-103+
(1) Measured on Mini-Circuits Characterization test board TB-313. See Characterization Test Circuit (Fig. 1)
(2) Current increases at P1dB
Parameter Condition
(GHz)
Vd=5V Vd=3V
Min. Typ. Max. Typ. Units
Frequency Range 0.05 4.0 GHz
Gain 0.05 — 26.5 — 25.9 dB
0.4 — 22.1 — 21.6
1.0 14.7 16.2 18.0 15.8
2.0 — 11.0 — 10.6
3.0 — 8.1 — 7.7
4.0 — 6.2 — 5.9
Noise Figure 0.05 0.5 0.5 dB
0.4 0.5 0.5
1.0 0.6 0.6
2.0 0.9 0.9
3.0 1.2 1.2
4.0 1.5 1.4
Input Return Loss 0.05 — 6.7 — 6.1 dB
0.4 — 11.3 — 10.4
1.0 10.0 13.0 — 12.0
2.0 — 12.8 — 13.0
3.0 — 13.7 — 13.0
4.0 — 15.0 — 14.2
Output Return Loss 0.05 — 14.1 — 13.8 dB
0.4 — 23.8 — 25.5
1.0 10.0 21.8 — 30.6
2.0 — 20.6 — 26.4
3.0 — 17.2 — 20.8
4.0 — 16.0 — 19.2
Reverse Isolation 1.0 21.2 20.5 dB
Output Power @1 dB compression(2) 0.05 20.0 15.4 dBm
0.4 21.5 18.2
1.0 22.5 18.7
2.0 22.5 19.3
3.0 22.9 20.0
4.0 23.2 20.7
Output IP3 0.05 — 36.7 — 32.4 dBm
0.4 — 39.0 — 34.1
1.0 — 41.9 — 34.5
2.0 40.0 44.6 — 35.6
3.0 — 44.3 — 35.6
4.0 — 45.4 — 35.3
Device Operating Voltage 4.8 5.0 5.2 3.0 V
Device Operating Current 97 120 60 mA
Device Current Variation vs. Temperature -178 -54 μA/°C
Device Current Variation vs Voltage 0.014 0.018 mA/mV
Thermal Resistance, junction-to-ground lead 36 36 °C/W
Notes
A. Performance and quality attributes and conditions not expressly stated in this specification document are intended to be excluded and do not form a part of this specification document.
B. Electrical specifications and performance data contained in this specification document are based on Mini-Circuit’s applicable established test performance criteria and measurement instructions.
C. The parts covered by this specification document are subject to Mini-Circuits standard limited warranty and terms and conditions (collectively, “Standard Terms”); Purchasers of this part are entitled
to the rights and benefits contained therein. For a full statement of the Standard Terms and the exclusive rights and remedies thereunder, please visit Mini-Circuits’ website at www.minicircuits.com/MCLStore/terms.jsp
Mini-Circuits®
www.minicircuits.com P.O. Box 350166, Brooklyn, NY 11235-0003 (718) 934-4500 sales@minicircuits.com
Monolithic E-PHEMT MMIC Amplifier
Page 4 of 5
PGA-103+
Fig 1. Block Diagram of Test Circuit used for characterization. (DUT tested on Mini-Circuits Characterization test board TB-313)
Gain, Return loss, Output power at 1dB compression (P1 dB) , output IP3 (OIP3) and noise figure measured using Agilent’s N5242A
PNA-X microwave network analyzer.
Conditions:
1. Gain and Return loss: Pin= -25dBm
2. Output IP3 (OIP3): Two tones, spaced 1 MHz apart, 5 dBm/tone at output.
Characterization Test Circuit
P103
Recommended Application Circuit
Product Marking
TB-313
Vcc (Supply Voltage)
Vd
Bias-Tee
ZX85-12G-S+
BLK-18+
RF-IN RF-OUT
DUT
1
2,4
3 3/5V
Cblock=0.001μF, Bias-Tee=TCBT-14+, Cbypass=0.1μF
Fig 2a. Evaluation board TB-678-103+ includes case, connectors and
components soldered to PCB
Fig 2b. Evaluation board TB-761-103+ unconditionally stable
(see note AN-60-064)
SEQ Manufacturer P/N / Value Size
A1 PGA-103+ —
C1, C2 .01 uF 0805
C3 0.33 uF 1206
C4 10 uF 1206
C5 330 pF 0603
L1 TCCH-80+ —
L2 620 nH .115X.110
R2 150 Ohm 0603
Notes
A. Performance and quality attributes and conditions not expressly stated in this specification document are intended to be excluded and do not form a part of this specification document.
B. Electrical specifications and performance data contained in this specification document are based on Mini-Circuit’s applicable established test performance criteria and measurement instructions.
C. The parts covered by this specification document are subject to Mini-Circuits standard limited warranty and terms and conditions (collectively, “Standard Terms”); Purchasers of this part are entitled
to the rights and benefits contained therein. For a full statement of the Standard Terms and the exclusive rights and remedies thereunder, please visit Mini-Circuits’ website at www.minicircuits.com/MCLStore/terms.jsp
Mini-Circuits®
www.minicircuits.com P.O. Box 350166, Brooklyn, NY 11235-0003 (718) 934-4500 sales@minicircuits.com
Monolithic E-PHEMT MMIC Amplifier
Page 5 of 5
PGA-103+
Visual
Inspection
Electrical Test SAM Analysis
Reflow 3 cycles,
260°C
Soak
85°C/85RH
168 hours
Bake at 125°C,
24 hours
Visual
Inspection
Electrical Test SAM Analysis
Start
MSL Test Flow Chart
ESD Rating
Human Body Model (HBM): Class 1A (250 to <500V) in accordance with ANSI/ESD STM 5.1 - 2001
Machine Model (MM): Class M1(25V) in accordance with ANSI/ESD STM5.2-1999
MSL Rating
Moisture Sensitivity: MSL1 in accordance with IPC/JEDEC J-STD-020D
Attention
Observe precautions
for handling electrostatic
sensitive devices
Performance Data
Data Table
Swept Graphs
S-Parameter (S2P Files) Data Set (.zip file)
Case Style DF782 (SOT 89) Plastic package, exposed paddle
lead finish: tin-silver over nickel
Tape & Reel F55
Standard quantities available on reel 7” reels with 20, 50, 100, 200, 500 or 1K devices
Suggested Layout for PCB Design PL-313
Evaluation Board TB-678-103+
TB-761-103+ (see Application Note AN-60-064)
Environmental Ratings ENV08T1
Additional Detailed Technical Information
additional information is available on our dash board. To access this information click here
All Datasheets Cannot Be Modified Without Permission
Copyright © Each Manufacturing Company
This datasheet has been downloaded from:
datasheet.eeworld.com.cn
Free Download
Daily Updated Database
100% Free Datasheet Search Site
100% Free IC Replacement Search Site
Convenient Electronic Dictionary
Fast Search System
www.EEworld.com.cn


PGA-103+

上一篇:PGA-105+

下一篇:PGA-102+

相关新闻

相关型号