位置:51电子网 » 企业新闻

PMA4-33GLN+

发布时间:2019/11/8 10:03:00 访问次数:38发布企业:深圳市创宝来科技有限公司


Page 1 of 5
Notes
A. Performance and quality attributes and conditions not expressly stated in this specification document are intended to be excluded and do not form a part of this specification document.
B. Electrical specifications and performance data contained in this specification document are based on Mini-Circuit’s applicable established test performance criteria and measurement instructions.
C. The parts covered by this specification document are subject to Mini-Circuits standard limited warranty and terms and conditions (collectively, “Standard Terms”); Purchasers of this part are entitled
to the rights and benefits contained therein. For a full statement of the Standard Terms and the exclusive rights and remedies thereunder, please visit Mini-Circuits’ website at www.minicircuits.com/MCLStore/terms.jsp
Mini-Circuits®
www.minicircuits.com P.O. Box 350166, Brooklyn, NY 11235-0003 (718) 934-4500 sales@minicircuits.com
Monolithic Amplifier
The Big Deal
• Low noise figure, 0.47 dB typ. @ 900 MHz
• High gain, 39 dB typ. @900 MHz
• High OIP3, +40 dBm typ. at 900 MHz
Product Overview
Mini-Circuits PMA4-33GLN+ is an E-PHEMT based, low noise, dual chip, MMIC amplifier with a unique
combination of low noise, high gain and high IP3, making this amplifier ideal for sensitive, high-dynamicrange
receiver applications. This design operates on a single 5V supply, is well matched for 50Ω systems,
and comes in a 4mm x 4mm, low-profile package accommodating dense circuit board layouts.
Feature Advantages
Low noise, 0.47 dB at 0.9 GHz Enables lower system noise figure performance
High Gain
• 38.9 dB at 900 MHz
• 26.9 dB at 2000 MHz
High gain with low noise minimizes the effect of noise figure reduction resulting from
cascading of multiple stages and simplifies circuit design.
High IP3
• +40.4 dBm at 0.9 GHz
• +40.2 dBm at 2 GHz
Combination of low noise and high IP3 makes this MMIC amplifier ideal for use in low
noise receiver front end (RFE) as it gives the user advantages of sensitivity & two-tone
IM performance at both ends of the dynamic range.
High max input power
• +24 dBm
Ruggedized design provides high power handling for input powers common at receiver
inputs, eliminating the need for an external limiter in most cases.
4 x 4mm 16-lead MCLP package Provides low inductance, repeatable transitions, and excellent thermal contact to PCB
High reliability
Low signal operating current of 154 mA nominal maintains junction temperatures typically
below 103°C at 85°C ground lead temperature.
Key Features
4mm x 4mm
PMA4-33GLN+
50Ω 0.7 to 3.0 GHz
Low Noise, High Gain & IP3
Page 2 of 5
Notes
A. Performance and quality attributes and conditions not expressly stated in this specification document are intended to be excluded and do not form a part of this specification document.
B. Electrical specifications and performance data contained in this specification document are based on Mini-Circuit’s applicable established test performance criteria and measurement instructions.
C. The parts covered by this specification document are subject to Mini-Circuits standard limited warranty and terms and conditions (collectively, “Standard Terms”); Purchasers of this part are entitled
to the rights and benefits contained therein. For a full statement of the Standard Terms and the exclusive rights and remedies thereunder, please visit Mini-Circuits’ website at www.minicircuits.com/MCLStore/terms.jsp
Mini-Circuits®
www.minicircuits.com P.O. Box 350166, Brooklyn, NY 11235-0003 (718) 934-4500 sales@minicircuits.com
Monolithic Amplifier
simplified schematic & pad description
Function Pad Number Description (See Figure 1)
RF IN Q1 2 Connects to RF input via C1 and Pad 3 via L1
RF-OUT Q1 & DC IN 5 Connects to RF IN Q2 via C2 and VS via L2
V Bias Q1 4 Connects to Supply voltage VS via R1
RF-GND Q1 3 Connects to ground via C4/C5
RF-IN Q2 8 Connects to RF OUT Q1 via C2
RF-OUT Q2 & DC IN 11 Connects to RF OUT via C3 and VS via L3
Ground Paddle Connects to ground
No Connection 1,6,7,9,10,12 to 16 Not used internally. Connected to ground on test board
CASE STYLE: DG1886
PMA4-33GLN+
Product Features
• Low Noise figure, 0.54 dB at 900 MHz
• High IP3, 40 dBm typ. at 900 MHz
• High Pout, P1dB 22.6 dBm typ. at 900 MHz
• High Gain, 39 dB at 900 MHz
REV. A
M151107
PMA4-33GLN+
TH/RS/CP
150924
General Description
The PMA4-33GLN+ (RoHS compliant) is a dual chip amplifier fabricated using E-PHEMT technology. It
offers extremely high dynamic range with high gain. It has repeatable performance from lot to lot and is
enclosed in a 4mm x 4mm low profile package for very good thermal performance.
Typical Applications
• Base station infrastructure
• Portable Wireless
• LTE
• GPS
• GSM
• Airborne radar
0.7-3.0 GHz
Low Noise, High Gain & IP3
+RoHS Compliant
The +Suffix identifies RoHS Compliance. See our web site
for RoHS Compliance methodologies and qualifications
RF GND Q1 RF OUT Q1 & DC IN RF GND Q1
RF IN Q1
Vbias Q1
PADDLE
RF OUT Q2 & DC IN
RF OUT Q1 & DC IN
RF OUT Q2 & DC IN
RF GND Q1 RF OUT Q1 & DC IN RF GND Q1
RF IN Q1
Vbias Q1
PADDLE
RF OUT Q2 & DC IN
RF OUT Q1 & DC IN
RF OUT Q2 & DC IN
Monolithic E-PHEMT MMIC Amplifier
Page 3 of 5
Notes
A. Performance and quality attributes and conditions not expressly stated in this specification document are intended to be excluded and do not form a part of this specification document.
B. Electrical specifications and performance data contained in this specification document are based on Mini-Circuit’s applicable established test performance criteria and measurement instructions.
C. The parts covered by this specification document are subject to Mini-Circuits standard limited warranty and terms and conditions (collectively, “Standard Terms”); Purchasers of this part are entitled
to the rights and benefits contained therein. For a full statement of the Standard Terms and the exclusive rights and remedies thereunder, please visit Mini-Circuits’ website at www.minicircuits.com/MCLStore/terms.jsp
Mini-Circuits®
www.minicircuits.com P.O. Box 350166, Brooklyn, NY 11235-0003 (718) 934-4500 sales@minicircuits.com
Absolute Maximum Ratings4
Parameter Ratings (Q1) Ratings (Q2)
Operating Temperature (ground lead) -40°C to 85°C -40°C to 85°C
Storage Temperature -65°C to 150°C -65°C to 150°C
Total Power Dissipation 0.55W 1W
Input Power (CW) +24dBm (5 minutes max)(Note 5)
+21 dBm (50-2000 MHz)
+26 dBm (2000-3000 MHz) (Note 6)
Q1 & Q2 cascade on TB-754+ +24 dBm
DC Voltage 5.5 V 6V
4. Permanent damage may occur if any of these limits are exceeded.
Electrical maximum ratings are not intended for continuous normal operation.
5. Measured on Mini-Circuits test board, TB-615+
6. Measured on Mini-Circuits test board, TB-313
PMA4-33GLN+
Electrical Specifications1 at 25°C and 5V, unless noted
Parameter Condition (GHz) Min. Typ. Max. Units
Frequency Range 0.7 3.0 GHz
Noise Figure
0.7 0.53 —
dB
0.9 0.47 0.85
1.5 0.66 —
2.0 0.91 —
3.0 1.79 —
Gain
0.7 — 41.3
dB
0.9 35.0 38.9
1.5 — 31.8
2.0 — 26.9
3.0 — 18.0
Input Return Loss
0.7 9.1
dB
0.9 12.3
1.5 13.0
2.0 11.6
3.0 9.4
Output Return Loss
0.7 5.5
dB
0.9 10.0
1.5 12.8
2.0 6.7
3.0 7.0
Output Power @1 dB compression2
0.7 22.5
dBm
0.9 22.6
1.5 22.6
2.0 22.9
3.0 20.6
Output IP3
0.7 35.8
dBm
0.9 40.4
1.5 41.0
2.0 40.2
3.0 35.7
Device Operating Voltage 5.0 V
Device Operating Current 55 —
Q22 97 — mA
Total2 152 186
Device Current Variation vs. Temperature at 5V3 -135 μA/°C
Device Current Variation vs. Voltage at 25°C 0.027 mA/mV
Thermal Resistance, junction-to-ground lead 53 (Q1), 36 (Q2) °C/W
1. Measured on Mini-Circuits Characterization test board TB-754+. See Characterization Test Circuit (Fig. 1)
2. Current increases at P1dB
3. (Current at 85°C -
Current at -45°C)/130
Monolithic E-PHEMT MMIC Amplifier
Page 4 of 5
Notes
A. Performance and quality attributes and conditions not expressly stated in this specification document are intended to be excluded and do not form a part of this specification document.
B. Electrical specifications and performance data contained in this specification document are based on Mini-Circuit’s applicable established test performance criteria and measurement instructions.
C. The parts covered by this specification document are subject to Mini-Circuits standard limited warranty and terms and conditions (collectively, “Standard Terms”); Purchasers of this part are entitled
to the rights and benefits contained therein. For a full statement of the Standard Terms and the exclusive rights and remedies thereunder, please visit Mini-Circuits’ website at www.minicircuits.com/MCLStore/terms.jsp
Mini-Circuits®
www.minicircuits.com P.O. Box 350166, Brooklyn, NY 11235-0003 (718) 934-4500 sales@minicircuits.com
PMA4-33GLN+
Recommended Application and Characterization Test Circuit
Product Marking
MCL
33GLN
black body
model family designation
index over pin 1
Fig 1. Application and Characterization circuit
Note: This block diagram is used for characterization. (DUT soldered on Mini-Circuits Characterization test board TB-754+)
Gain, Return loss, Output power at 1dB compression (P1 dB), output IP3 (OIP3) and noise figure measured using Agilent’s
N5242A PNA-X microwave network analyzer.
Conditions:
1. Gain and Return loss: Pin= -40 dBm
2. Output IP3 (OIP3): Two tones, spaced 1 MHz apart, 5 dBm/tone at output.
BOM of Test Board TB-754+
SEQ Size Description
DUT 4x4 mm PMA4-33GLN+ Amplifier
L1 0402 Inductor 15nH
L2 0402 Inductor 5.6nH
L3 0402 Inductor 82nH
C1 0402 Capacitor 56pF
C2 0402 Capacitor 82pF
C3 0402 Capacitor 68pF
C4 0402 Capacitor 1000pF
C5 to C8 0402 Capacitor 0.1μF
R1 0402 Resistor, 1kΩ
Monolithic E-PHEMT MMIC Amplifier
Page 5 of 5
Notes
A. Performance and quality attributes and conditions not expressly stated in this specification document are intended to be excluded and do not form a part of this specification document.
B. Electrical specifications and performance data contained in this specification document are based on Mini-Circuit’s applicable established test performance criteria and measurement instructions.
C. The parts covered by this specification document are subject to Mini-Circuits standard limited warranty and terms and conditions (collectively, “Standard Terms”); Purchasers of this part are entitled
to the rights and benefits contained therein. For a full statement of the Standard Terms and the exclusive rights and remedies thereunder, please visit Mini-Circuits’ website at www.minicircuits.com/MCLStore/terms.jsp
Mini-Circuits®
www.minicircuits.com P.O. Box 350166, Brooklyn, NY 11235-0003 (718) 934-4500 sales@minicircuits.com
PMA4-33GLN+
ESD Rating
Human Body Model (HBM): Class 1A (250 to <500V) in accordance with ANSI/ESD STM 5.1 - 2001
Machine Model (MM): Class M1 (pass 25V) in accordance with ANSI/ESD STM5.2-1999
MSL Rating
Moisture Sensitivity: MSL1 in accordance with IPC/JEDEC J-STD-020D
Performance Data
Data Table
Swept Graphs
S-Parameter (S2P Files) Data Set (.zip file)
Case Style DG1886 Plastic package, exposed paddle, lead finish: tin-silver over nickel
Tape & Reel F68
Standard quantities available on reel 7” reels with 20, 50, 100, 200, 500,1K or 13” reel with 2K devices
Suggested Layout for PCB Design PL-407
Evaluation Board TB-754+
Environmental Ratings ENV08T1
Additional Detailed Technical Information
additional information is available on our dash board. To access this information click here
MSL Test Flow Chart
Additional Notes
A. Performance and quality attributes and conditions not expressly stated in this specification document are intended
to be excluded and do not form a part of this specification document.
B. Electrical specifications and performance data contained in this specification document are based on Mini-Circuit’s
applicable established test performance criteria and measurement instructions.
C. The parts covered by this specification document are subject to Mini-Circuits standard limited warranty and terms
and conditions (collectively, “Standard Terms”); Purchasers of this part are entitled to the rights and benefits
contained therein. For a full statement of the Standard Terms and the exclusive rights and remedies thereunder,
please visit Mini-Circuits’ website at www.minicircuits.com/MCLStore/terms.jsp
Visual
Inspection
Electrical Test SAM Analysis
Reflow 3 cycles,
260°C
Soak
85°C/85RH
168 hours
Bake at 125°C,
24 hours
Visual
Inspection
Electrical Test SAM Analysis
Start
Finish
All Datasheets Cannot Be Modified Without Permission
Copyright © Each Manufacturing Company
This datasheet has been downloaded from:
datasheet.eeworld.com.cn
Free Download
Daily Updated Database
100% Free Datasheet Search Site
100% Free IC Replacement Search Site
Convenient Electronic Dictionary
Fast Search System
www.EEworld.com.cn


PMA4-33GLN+

上一篇:TH72012

下一篇:PMA3-83LN资料

相关新闻

相关型号